Nucrel 0910

Resins

SKU: 210001

Nucrel 0910

Nucrel 0910 is a copolymer of ethylene and methacrylic acid. The resin is available for use in conventional extrusion and coextrusion equipment.

Extrusion Coating/Lamination

Extrusion Coating/LaminationNominal Values
Processing InformationA suggested extruder set temperature profile.
Feed Zone185°C (365°F)
Second Zone235°C (455°F)
Third Zone260°C (500°F)
Fourth Zone285°C (545°F)
Fifth Zone285°C (545°F)
Adapter Zone285°C (545°F)
Die Zone285°C (545°F)

General Processing Information

Nucrel 0910 is normally processed at melt temperatures ranging from 260°-305°C (500°-581°F) in flat die equipment. For extrusion coating and laminating, a typical extruder profile is below. Actual processing temperatures will usually be determined by either the specific equipment or substrate or one of the other polymers in a coextrusion. Materials of construction used in the processing of this resin should be corrosion resistant. Stainless steels of the types 316, 15-5PH, and 17-4PH are excellent, as is quality chrome or nickel plating, and in particular duplex chrome plating. Type 410 stainless steel is satisfactory, but needs to be tempered at a minimum temperature of 600°C (1112°F) to avoid hydrogen-assisted stress corrosion cracking. Alloy steels such as 4140 are borderline in performance. Carbon steels are not satisfactory. While stainless steels can provide adequate corrosion protection, in some cases severe purging difficulties have been encountered. Nickel plating has been satisfactory, but experiments have shown that chrome surfaces have the least adhesion to acid based polymers. In recent years, the quality of chrome plating has been deteriorating due to environmental pressures, and the corrosion protection has not always been adequate. Chrome over top of stainless steel seems to provide the best combination for corrosion protection and ease of purging. If surface properties of the extruded resin require modification (such as, lower C.o.F. for packaging machine processing), refer to the CONPOL™ Processing Additive Resins product information guide. After processing NUCREL™, purge the material out using a polyethylene resin, preferably with a lower melt flow rate than the NUCREL™ resin in use. The "Disco Purge Method" is suggested as the preferred purging method, as this method usually results in a more effective purging process. Information on the Disco Purge Method can be obtained from Formula Chemicals. Never shut down the extrusion system with NUCREL™ in the extruder and die. Properly purge out the NUCREL™ with a polyethylene, and shut down the line with polyethylene or polypropylene in the system.

FDA Status Information

Nucrel 0910 complies with Food and Drug Administration Regulation 21 CFR 177.1330(a) - - Ionomeric resins, subject to the limitations and requirements therein. This Regulation describes polymers that may be used in contact with food, subject to the finished food-contact article meeting the extractive limitations under the intended conditions of use, as shown in paragraph (c) of the Regulation.

Regulatory Information

For information on regulatory compliance outside of the U.S.A., consult your Formula Chemicals representative.

Safety & Handling

For information on appropriate Handling & Storage of this polymeric resin, please refer to the material Safety Data Sheet. A Product Safety Bulletin, material Safety Data Sheet, and/or more detailed information on extrusion processing and/or compounding of this polymeric resin for specific applications are available from Formula Chemicals.

Price

Request Quote

kg

Port of Origin: Shanghai

1 Pallet

Compare Products

Technical Documents

Technical data sheet

Download TDS · English

version 22 Oct 2026

Other languagesEspañolPortuguêsFrançaisDeutsch日本語한국어中文(简体)中文(繁體)Türkçeالعربية

Physical Data


Density (g/cm³)

0.93


Melting point

100°C (212°F)


Composition

8.7% By Weight Methacrylic Acid comonomer content


Melt Flow Index (190°C/2.16kg)

10.0 g/10 min


Freezing Point (DSC)

82°C (179.6°F)


Vicat Softening Point

81°C (177.8°F)


Maximum Processing Temperature

310°C (590°F)


Applications

Recommended

Limited Suitability

Not Recommended

COATINGS


Automotive Coating


Industrial Coating


Decorative Coating


Coil Coating


Wood Coating


Powder Coating


PLASTICS


PVC


PE/PP/PO


ABS


PS


PA


Rubber


INKS


Offset


Solvent based


Water based


UV / EB


Inkjet


Acrylic


Logistics, shelf life and storage


Port of Origin 1

Shanghai


Shipping Net Kg/Pallet

1000


Pal Length

1.15


Pal Width

1.15


Pal Height

1.15


Lead Time (days)

30


Related Products

Dispersing Agent DA27K
Dispersing Agent DA27K

Color Index: N/A

Need a Custom Solution?

A quick reminder that Formula is here to help solve even the most complex problems.

PigmentsAdditivesResinsUV materials
Privacy PolicyCookie PolicyCookie preferencesTerms and ConditionsReturn PolicyDisclaimer
Formula Chemicals Logo

Copyright © 2026 Formula Chemicals Inc. All rights reserved.